603 - 5885 1250 (4 lines) info@mes100.com
View Categories

Gridded HP1 and HP26 IDF Coefficients

Most design sites are not next to a rain gauge. Before HP1 (2021) and HP26 (2018), the engineer picked the nearest MSMA2 station and used its fitted λ, κ, θ and η, even when that station was 30 km away and on the other side of a ridge. HP1 and HP26 now publish the same four coefficients on 10 km and 20 km grids covering Peninsular Malaysia (HP1) and Sabah and Sarawak (HP26). In this article we set up a Storm Sync project to read its IDF coefficients from the grid cell that contains the design site, and we show how to check which cell and which numbers a run used.

How the grid gives the IDF #

Each published grid cell carries a centre coordinate and the four coefficients of the generalized IDF equation:

i = \dfrac{\lambda T^{\kappa}}{(d + \theta)^{\eta}}

where:

  • i is the rainfall intensity in mm/hr
  • T the ARI in years
  • d the storm duration in hours.

This is the same equation the MSMA2 rain gauges use, so only the source of λ, κ, θ and η changes; the drain and Time Area calculations downstream are unchanged.

MiTS looks up the cell whose published centre is nearest to the design site. The site must lie within half a cell diagonal of that centre (about 7 km on the 10 km grid, 14 km on the 20 km grid); a site further out, for example offshore or across the national border, is rejected rather than snapped to a distant cell. The tables publish centre coordinates, not cell polygons, so the cell outlines drawn on the map are nominal.

HP1 recommends the 10 km grid for small catchments and the 20 km grid for medium and large ones, subject to the local authority’s requirement. MiTS does not pick the resolution from the catchment size, and it does not average coefficients over a basin as the HP1 and HP26 basin examples do. It uses the point cell.

Selecting the grid #

Steps: #

  1. Go to Options > Project Settings > Storm Design > Design Rainfall > Malaysia > Rainfall Intensity, OR step 2 of Project Setup. The design standard must be MSMA 2nd or 3rd Edition.
  2. Set IDF source to Gridded HP1 / HP26.
  3. Under Grid selection, choose where the cell comes from with Grid IDF from:
    • Project site: the cell at the project site set in Project Setup. Change project site… takes you there.
    • Another point: the cell at a different latitude and longitude (WGS84), for example a catchment some distance from the site pin. Type the coordinates or click the map; they start at the project site.
    • Published grid number: choose the Published table (HP1 or HP26) and type the grid number, for example when the authority has already specified the cell. MiTS starts from the cell nearest the project site, so often you only change the number. No design-site coordinate is assumed.
  4. Choose the Grid resolution: 10 km (small catchments) or 20 km (medium / large catchments). The labels repeat HP1’s recommendation; the choice is still yours.
  5. Check the cell. For the two point choices, MiTS picks HP1 or HP26 from the nearest published centre and shows that publication and the cell’s number in Grid number to use, greyed out, with its distance from the point and its four coefficients. To use a different cell, switch to Published grid number; only then can the number be typed.

If the cell moves between HP1 and HP26, for example when the point moves from Peninsular Malaysia to Sarawak, the temporal-pattern reference follows it and the region is cleared for you to choose again.

Read-only published coefficient table, based on MSMA2


Gridded HP1/HP26 coefficient based on project site latitude and longitude


Editable Grid Number and coefficients based on HP1/HP26

Climate change factor #

CCF inclusion sits beside the IDF source at the top of the page and is on by default.

  • HP1 (Peninsular Malaysia): the CCF depends on the region in HP1 Figure 8.3 (Tables 8.1–8.5), which a grid number alone does not determine. Choose the HP1 CCF region. MiTS suggests one from the state of the listed town nearest the site or point, but check it against the map near mountains, Kuala Lumpur and regional edges. Click View HP1 CCF region map to see Figure 8.3. These CCF regions are separate from the temporal-pattern regions.
  • HP26 (Sabah and Sarawak): the CCF is read from the selected grid cell and ARI; there is nothing to choose.

HP1 CCF region picker following Figure 8.3

The areal reduction factor is not applied to gridded coefficients.

Check what a run used #

The project saves the site, resolution and grid selection, not the coefficients. If you change the grid afterwards, the existing report still shows values from previous run, that is until you rerun the analysis.

The detailed drainage textual report and the Storm Sync run summary name the source as Gridded HP1 / HP26 and give the publication, resolution and grid number used, the λ, κ, θ, η and CCF used, and the data hash. The Hydrology Excel report’s Rainfall sheet lists the source, the four coefficients and the CCF for each analysed ARI.

Detailed Hydrology Report that displays the gridded number, coefficients, CCF and ARF

Worked check #

HP26 Table 5.1 gives the 10-year, 1-hour rainfall intensity at 20 km Grid 39 as 87.45 mm/hr. With that cell’s λ = 66.1810 and its κ, θ and η, MiTS calculates 87.4493 mm/hr, which rounds to the published value. HP26’s prose on the same page quotes λ = 66.1870, which would round to 87.46; we keep the table and map value.

Comparison of the 1-hour rainfall intensity between HP26 and MiTS computation

Conclusion #

For an ungauged site, the gridded source replaces “nearest station” with “the published cell the site lies in”. Do confirm the resolution the authority expects, review the cell on the map, choose the HP1 CCF region yourself, and check the grid number and data hash in the report before submission is done.

Powered by BetterDocs